SCS on the body 

References
HCOB 18 May 1980 "Start - Change - Stop Commands" 
HCOB 28 July 1958 "Clear Procedure" 
HCOB 15 October 1958 "ACC Clear Procedure" 
HCO Processing Sheet 20 September 1956 
HCO Training Bulletin 6 February 1957 
HCO Training Bulletin 30 November 1956 
PAB No. 87 "Scientology Processing" 
PAB No. 97 "Start-Change-Stop" 
Tape: 5905 C27 LACC-8 "Clearing General Processes: Lecture II" 
Tape: 5811C19 "Attitude and Approach in Auditing" 
Tape: 5608XX "Start Change Stop" 
Tape: 5609C02 GC-13 "Demonstration of SCS" 
Fundamentals of Thought 
Control and the Mechanics of SCS 


Description
The second stage of running Start-Change-Stop is SCS on the body . 
The person is, at this point, processed towards the ability to be in
control of his body . 

One meets with three conditions in processing: the person who is
compulsively interiorized, the person who compulsively exteriorized, and
the person who is buttered all over the universe. The case run on S-C-S
would greatly accumulate the ability collect himself. This might not occur
until you have run him for five or more hours on it. 

If this process is continued long enough, the person will be moving his
body by postulate (i.e., from the outside), not by beams,
stimulus-response, etc. 

To run this process, the processor and person should both stand up. This
gives reality, and the processor duplicating the person will bring about
greater ARC. The session always fails when the processor sits down while
running SCS. 


Commands
Each time, you make a contract with the person. You don't depend on any
former understanding with this process. Each moment in time is new. We make
each move in time a new move. He doesn't have to depend on his memory, so
you repeat again each time. The whole wording is given. 
Start: Processor is in physical contact with the person when giving the
R-factor each time. 


"I am going to ask you to start the body. I am not going to ask you to stop." 
"When I ask you to start the body, start the body, okay?" 
"Start." 
"Did you start the body?" 
Repeat commands 1234, 1234, until the person is easily doing the commands
on that subject. 
Change: The processor distributes four spots of tape or paper around the
floor in a new unit of time, each time the process is cycled through.
Processor is in physical contact with the person when giving the R factor
each time. 


"This spot we are going to call 'A'." (Processor indicates spot 'A' with a
marked piece of paper on the floor.) 
"This spot we are going to call 'B'." (Processor indicates spot 'B' with a
marked piece of paper on the floor.) 
"This spot we are going to call 'C'." (Processor indicates spot 'C' with a
marked piece of paper on the floor.) 
"This spot we are going to call 'D'." (Processor indicates spot 'D' with a
marked piece of paper on the floor.) 
"When I ask you to change the body; I want you to change the body's
position from 'A' to 'B'. Do you understand that?" 
"Change." 
"Did you change the body?" 
"When I ask you to change the body; I want you to change the body’s
position from 'B' to 'C'. Do you understand that?" 
"Change." 
"Did you change the body?" 
"When I ask you to change the body; I want you to change the body's
position from 'C' to 'D'. Do you understand that?" 
"Change." 
"Did you change the body?" 
Repeat the commands, 1-13, 1-13, until the person is easily doing the
commands on that subject. The locations of the designated spots do not have
to be the same as the previous time as it makes the process too much like
duplication, brings the person to predict the process too easily and he
will do it machinewise. 
Stop: Processor is in physical contact with the person when giving the
R-factor each time. 

"I am going to ask you to get the body moving in that direction (indicates
direction with her hand). Somewhere along the time, I will tell you to
stop. Then you stop the body. Do you understand?" 
"Get the body moving." 
"Stop!" 
'Did you stop the body?" 
Repeat commands 1-2-3-4 until the person is easily doing the commands on
that object. 
The processor would now run Start again on the same object and so on, until
neither Start, Change, nor Stop produces any changes. 

Stop Supreme: 

"I am going to ask you to get the body moving in that direction (indicates
direction with her hand). Somewhere along the time, I will tell you to
stop. And when I do, I want you to stop the body as fast as you can and
hold it as still as you can, okay?" 
"Get the body moving." 
"Stop!" 
'Did you do it?" 
Repeat commands 1-2-3-4 until the person is easily doing the commands on
that object. 
The processor would now run Start gain on the body and so on, until neither
Start, Change, Stop, nor Stop Supreme produces any changes. 

~~~~ 

Whenever the person is standing to execute a command, the processor is
standing next to the person. She also ensures that she is touching the
person (hand lightly on person's arm or elbow, etc.) when she gives the
person the R-Factor such as in steps 5, 8, and 11 above. 

The process, of course, always acknowledges the person for every execution
of a processing command. 


End Point
This process is run until neither Start, Change, Stop, nor Stop Supreme
produce change. The person will be able to do the steps of SCS easily and
will have a realization about starting, changing, and stopping the body.
This can happen at any point while running SCS on the body. 

Cautions
None.